Anchor line question

I have an anchor line question I hope someone has experience with. I purchased and installed a Powerwinch 31 anchor winch.
I would like to use 8 Plait line instead of 3 Strand.
I called Powerwinch because their literature recommends 3 strand or New England.
Powerwinch states they have not tested 8 plait so they do not have any data on if it will work with their Gypsy.
The 8 plait has been tested on Lewmar, Maxwell and another anchor winch that I can't remember the name of.
Does any one have experience using 8 plait in the Powerwinch 31? If not, is there any reason why it should not work? Will slippage be a problem under load because it is a softer lay than 3 strand?
I realy would like to use the 8 Plait, but don't want to invest in something that may not work.
Thanks for any input any one can offer.
 
I'm a huge fan of Yale yacht brait [not a spelling error] for anchor rode. Unfortunately, I can not give you advice where the Powerwinch 31 is concerned other than to say the diameter of the rode is usually the most important factor in retrieving your anchor not the lay of the line. Why not buy 15 or 20 feet of it and give it a try? You can always use it for a dock line after the test.
 
I can't give you a direct answer on this either, but I'm sure someone has tried 8-plait on a Powerwinch 31 and will chime in soon.

The way I understand it some of the new anchor windlasses are designed for 8-plait only. The flexibility of 8-plait line allows windlass designers to put tighter bends in the line path making a more compact windlass design possible. So while you may not be able to use 3-strand line in a windlass designed for 8-plait a windlass designed for 3-strand should be able to use either. In actual practice that doesn't seem to be the case. I've read reports from ROs here that there are chain/line combination windlasses that just don't seem to like 8-plait at all.

New and dry 8-plait can slip as well. After the line is wet or used there there doesn't seem to be an issue.
 
The most critical part of anchor line is its elasticity. That is why 3 strand is usually recommended - it can stretch 30 to 40%. The elasticity absorbs the wave and wake shock and prevents the anchor from being jerked out of bottom. Many 8 plait lines have little or no elasticity. Be sure to check the specs before ordering any.
 
Anchor line??? Les, you've been landlocked too long!
 
I have a maxwell 500 on my boat.. I was going to order new 8 plait and more chain (pre-spliced) considering it a worthy upgrade.. Thanks Les!.. I will now order 3 strand instead, it's cheaper.I hope it works w/ my windlass?. I thought I had read numerous times that 8 plait was better than 3 strand but I don't want to give up that elasticity especially after being on the hook yesterday in 20mph winds gusting to 35. Forecast was for 10-15mph before we left on Tues.. Forecast "changed" wed. morning, I was worried my camper canvas was going to blow off as well as being worried about the anchor and rode... This is our second season with our little cruiser and every trip is still a learning experience.
 
There is something both inspiring and reassuring when you hear a good 3-strand anchor line creaking on a bow chock some windy night. It means there is pull on the anchor, the chain is starting to pick up and the line is stretching. Everything is doing it's job.
 
TIC
I have a Maxwell 500 windlass on my boat. The boat was delivered with 200' of 1/2" 8 strand yacht brait and the rode worked perfectly. I needed a longer rode so I installed a 1/2" 3 strand rode that I already owned. It would NOT work. I tried everything. Trailing the bitter end, fabric softner, you name it. I had jams and hockles. I couldn't pull the anchor twice in a row without a problem. I had a guy from New Zealand on the boat that knew the Maxwell windlass and he noticed the problem instantly. He told me to switch back to yacht brait and my problems would go away. Anyway, I switched to a longer rode with yacht brait and haven't had one jam or hockle since. YMMV
 
RE: Les' comments on elsaticity

Yale PDF catalog, page 5, describes yacht brait as having greater elasticity than three strand. So, based on the mfgr comments, it would seem that some 8-strand lines ( ie: Yale ) would be acceptable. YMMV.
 
quote:

Originally posted by Les Hall

The most critical part of anchor line is its elasticity. That is why 3 strand is usually recommended - it can stretch 30 to 40%. The elasticity absorbs the wave and wake shock and prevents the anchor from being jerked out of bottom.





The chain lying on the bottom helps also. As the boat pulls on the rode, the chain is raised and its weight acts as a hock absorber. Both are important.
 
quote:

Originally posted by ctcruiser
[brOn the end of my rope anchore line the meteal eye has rusted and I bent it on accident last year when it got hung up on something. Can I rplace this without having to resplice the line?





It's called a "thimble". They are available in metal and nylon. You might be able to work a nylon thimble in.

If you decide to resplice it, you can switch the line end for end so you have "new" line at the working end.
 
quote:

Originally posted by MikeeH

........I first removed and reversed all the rode so I was now using the "clean" end of the rode. If you chose to go this route its also advisable to first remove the anchor and then, while cruising slowly in a straight line, feed all the rode out so it trails behind the boat. This will remove any twists or coils that have developed. You can then begin bringing the rode in and coiling in in the locker "dirty end" first. Just make certain you have a second person aft to make sure it doesn't get into your prop.






Or do this in reverse.
 
Shake n Bake;. Thanks.. I checked the maxwell website and it said the freedom 500 will work with either 8 plait OR 3 strand. However I'm sure it works better w/ 8 plait. I don't want the agony of a constantly jamming windlass so I think I'll stick w/ 8 plait and look into Yale yacht brait since others have posted good things about it as well.
 
Back
Top