Bottom Paint, cost?

aholst1

Member
exMember
Joined
Apr 20, 2006
RO Number
20936
Messages
446
Hi all, I am getting ready to introduce a marine coating system that will provide anti-fouling properties for 8 - 10 years in severe salt water conditions and 12-15 in freshwater. More importantly, zebra and quagga mussells WILL NOT adhere to this coating (it's environmentally friendly and approved for use) For the zebra mussell solution, from an industrial coating standpoint, cost is not an issue as compared to maintenance requirements to keep critical underwater structures mussell free. Looking from a recreational boating standpoint, what is the cost for a super-high quality anti-fouling bottom paint - Material cost for the DIY'er? Installed cost for the contractor? In your opinion(s) how much is too much?
 
$200 / gal tops for Micron Extra and $17/ft for the marina to paint the bottom, incl materials.
 
Not all that sophisticated but I bought a dented can of Interlux for $80, two sheets of #80 grit sandpaper for $.89 each, and a houshold paint roller kit for $5.99. I had some blue masking tape so I didn't need to purchase any of that.

The total was less than $100 when even I factor in the beer my friends drank while they watched me work so I'm very happy.
Jim
 
I have two fresh water boats and don't use bottom paint however these boats haven't seen Zebra muscles. The 26 foot "fresh water" boat does spend a month at a time in salt water. Any growth in the month rinses of with "On and Off".

I don't know haw many people plan of keeping their boat eight years and would be willing to pay much extra for that.

I have sound that "severe salt water condiitons" are usually warm, brackish water in isolated locations.

Do you have any ballpark costs yet? IMHO cost is always an issue. Perhaps it is my Scottish heritage.
 
RB, the base coat will run about $95/gal and will cover 150 sq.ft rb2@gr5t 10 mils DFT (dry film thickness) This coat is 100% environmentally safe - it has NSF / ANSI std 61 approval for potable water systems and is approved for use in fisheries (pond linings, etc.) The top coat, "Zebra Mussell Solution" - I am waiting for all the tech data and cost. "High" was used when I spoke to the manufacturer...
 
I think you need a test boat to see how well it is going to work. I could help out on that end in a nice warm cilmate. Barnacles start to grow in a couple of weeks in my canal. You can let me know if you need a test boat.
 
and you'll need to test in the northeast as well. hint, hint. here it costs approx $215 for the high end ablative anti-fouling paint. not sure of the marina cost as i either do it myself or hire cheap day labor.
 
Interlux Micron Extra lists for $240/gal....$20 off at WM for net of $220/gal.
Don't forget your 7% for NJ governor ! Now we're at $235/gal.
 
I can't fathom not hauling for 8 years. Prop dings, blister potential, rudder stuffing, detailing, etc....are all handled on shore. If you could deal with these problems as well, you may have something. I am sure the Navy would be interested. Me...not so much. Haul, clean the bottom, scrape, paint 2 coats, detail, lsunch.....Worst cases $1K.
 
$300 a gallon for the extended life would be attractive. $400, or double the usual, would be worth looking at.

Would this stuff likely stay on the running gear? The Florida canals such as the ones in Marathon or Ft Myers require running gear protection also.
 
This year I used Pettit Hydrocoat water based paint. It was on sale for $99 with $20 mail in rebate. Two coats with one gallon. I've read on this forum where folks on the Chesapeake have used and thought I'd try it. The cost of a sanding block and thinner was in the noise.
 
Thanks to everyone for your feedback...I am pretty sure this system will address all the concerns and potential objections above. The base coat is actually in use by the navy, with approval MIL-P-23380B Type II SH VOC Compliant for Anchor Chain. We have sell some every year for anchor chain coating for use on the USS Seawolf. The base coat is an amazing product, but alas no anti-fouling properties. It's the top coat I need the technical data on (adhesion / abrasion resistance) I do have some legit testing and case studies on the anti-fouling properties of the top coat which are remarkable.
 
It would be a difficult sell to state it lasts for 8-10 years in severe salt conditions, if you haven't been using it for 8-10 years let alone 12-15 in Freshwater. Have you? Any test data?
 
quote:

Originally posted by aholst1

Hi all, I am getting ready to introduce a marine coating system that will provide anti-fouling properties for 8 - 10 years in severe salt water conditions and 12-15 in freshwater. More importantly, zebra and quagga mussells WILL NOT adhere to this coating (it's environmentally friendly and approved for use) For the zebra mussell solution, from an industrial coating standpoint, cost is not an issue as compared to maintenance requirements to keep critical underwater structures mussell free. Looking from a recreational boating standpoint, what is the cost for a super-high quality anti-fouling bottom paint - Material cost for the DIY'er? Installed cost for the contractor? In your opinion(s) how much is too much?






I was searching for bottom paint this morning. Have you been able to cut a deal with International to bring Intersleek 900 to the consumer market? Wow!
 
Your going to introduce a new anti fouling paint as a business, you own a powerboat yourself and your asking here on a forum how much a gallon of bottom paint costs?

Sorry but the P.I. in me smells infomercial or sales pitch and you already know what a gallon of bottom paint costs.

Rename your thread, "Hey I'm selling some awesome bottom paint soon" .........

We should be honest with each other here.
 
JLC,
My business is industrial coatings, selling hundreds of gallons to a client; not bottom paint, selling 2- 3 gallons to you. If I can enter the bottom paint market, I will. My product is a high performance epoxy which is superior to every epoxy I have done a product comparison on. The topcoat is from a different manufacturer, tested with my product and is the perfect base coat. I see the benefit in terms of combatting the $1 billion annually in maintenance costs due to the zebra mussell crisis my clients and potential clients are facing.
I haven't had to bottom paint my boat so I have not incurred the cost. I have looked at pricing in the WM and BW big book, but have done no research on the 'net for comp pricing. I was attempting to get info from forum members for some "real world" insight to see if the product would be of interest in the recreational boating market and what "sticker-shock" would be.
I apologize if you or anyone felt this was an "info-merical" or dis-honest on my part. More importantly, I would not advertise any product for sale through the forum. If I choose to do so, the product would be sold through Les and Boatfix.
The topcoat manufacturer does have test data to support the percieved outrageous claims. What I don't have is the tech data sheets for coverage per gallon or recommended DFT. (no, it's not Intersleek)
To all, please accept my apologies for any perceived mis-use of the forum and thanks again for your feedback.
 
Keep us posted. I'd be interested in checking out the details when they're available.

Doug
 
Back
Top