Dock sanding

OldMariner32

Member
exMember
Joined
Apr 18, 2007
RO Number
25936
Messages
313
We are buying a lot with an old dock. The surface of the dock is weathered and rough. At our old yacht club, they appeared to have sanded the surface of the dock there giving a fresh, flush surface. My question is, how do you do that? It would seem that a belt sander would be eaten up by the nails through the dock decking. Any thoughts?
 
Try using a pressure washer instead of sanding...Results are great and it's less labour intensive...
Treat it with something like a Thompsons Water Sealer when done...
 
You can rent large circular sanders that are used to refurbish floors. You need to be somewhat big and strong to control these. Nails could potentially be a problem unless you are able to drive them somewhat past flush.

G
 
I would NOT use a pressure washer because 1) it forces water into the wood and 2) it will remove lots of the wood if you're not careful and 3) it removes the softer parts of wood, leaving the harder splinters (exactly what you don't want). Don't ask how I know this... May have ruined a deck recently. :-)

How about flipping the boards over? If they come off fairly easily you could also use a portable planer to surface one or both sides. I wouldn't do this without checking carefully for nails, however. This is what I did and it worked awesome - very quick and easy to rescrew the boards down when finished.
 
I don't think I can drive those nails flush which is why I ruled out the floor sander.

Good point about the pressure washer. I hate to think I have to remove the decking to get a good surface, but if that is what it takes . . .
 
quote:

Originally posted by gcolton

You can rent large circular sanders that are used to refurbish floors. You need to be somewhat big and strong to control these. Nails could potentially be a problem unless you are able to drive them somewhat past flush.

G






Those float? I could see this ending poorly. But funny. Man, would that be funny to hear abouta floor sander going off the end of the dock.
 
How about just covering with Trex or some other synthetic surface?
Even green grass carpet will get you another 5 years out of it.
 
Power washing can remove the softer "pulp" and speed up deteriotion. Turning the boards will produce cupping.
 
Congrats on the purchase. Not to rain on the parade here, but what is the condidion of the rest of the dock. If the substrate is in poor condition, you may be putting lipstick on a pig.

That said, if the rest of the structure is OK and the boards aren't in too bad shape, I would opt for flipping them if possible.

There are tons of products that you could do manually with a stiff bristle brush on a mop handle. Google "powdered wood cleaner" (no quotes) and you get tons of hits. I have heard good things about Wolman's.

HTH
 
an equally inexpensive way to spruce it up a bit is go to home depot and buy a couple cases of pool bleach its approx. 5% instead of 2% like at the grocery store. dilute it 50/50 and use a garden sprayer to apply it to the wood. use protective rubber gloves and shoes. let it sit for about 20 minutes and rinse it off. the bleach will attach the nails if they are exposed steel. if you already have s/s decks screws don't worry about them. this method will remove less of the material than pressure cleaning. yes in theory putting the boards crown down may cup them but on a seasoned board it is very unlikely. the deck is very likely P/T pine, very bad stuff to run thru a planer, the salt in P/T will eat blades. since the deck is not smooth like a wood floor and surrounded by water i would not use a floor sander. if you want to sand it by hand with a belt sander it will give you the best results, but take the most time. if you want the hottest looking dock around, buy mahogany planks. the hard wood will outlast the pine and will not warp nearly as much in the sun. all depends on whether you have more time than $ which is the best answer for you.
 
Yeah, stay away from the water pressure washer. We did that on our deck out back, and while it made it LOOK great, it really raised the gran and made it splinterville for the kids. I second the green (or better yet, blue) indoor/outdoor carpet.
 
Thanks for your feedback, everyone.

There is one punky piling that I plan to eventually replace, but for the most part I think it is structurally sound.

I do have more time than $, Vic33004, so I suspect there is a belt sander in my future. The nails appear to just be common nails, not galvanized or SS. Are you saying that the bleach will eat them up?

KiDa, thanks for the congrats.
 
Covering the wood with I/O carpeting will hasten the rotting of the wood. Only do that if you expect to replace all the deck boards within a couple of years! I second avoiding the pressure washer. A good stiff brush with a solution which includes bleach is best. Do not expect a boat dock to look like a backyard deck.........
 
tom, bleach will attack steel nails, even the galvanized ones. if you have common nails now and you have the time, just pull up the planks one at a time, sand the back side of them and reattach them with s/s deck screws. the best tool for pulling up the planks is an old logging tool used for turning logs. long handle with a hinged hook on it and a pointy end. if you're not worried about the rust on the nails don't worry about the bleach they are going to rust anyway. if you want to put a sealer on afterwards sikkins makes the most durable finish, but any finish you put down with time/sun will darken and be hot on the feet. depends how far south you are. if the planks are not P/T you can still use a planner if you pull em up and strip out the nails. it will make fast work of it to use the planner, but odds are you have P/T. since you already have rusty nails, my advice is use some household bleach first, test a section see if you are happy with it. you'll know in 10 minutes if it will work to your satisfaction. if you're not happy you know what you have to do.
 
Most of us in south Florida just use a stain wood treatment. You can get them in a few colors. Green and brown are popular. Get a thicker one like paint and it will fill a lot of the ruff wood . I preassure wash mine every couple of years let it dry a few days and paint it with a roller.
prom001.jpg
 
Randy,

That looks pretty good.

Unless somebody stops me, here's my plan:

Pool bleach mix and a stiff brush . . .

If that's not good enough, decide whether to sand or stain (I don't have a portable planer) depending on the condition I end up with.

Here is the before picture.

image3211.jpg


Stay tuned for the finished job.
 
Bleach is fine but they also sell deck cleaner at most stores. For all I know it's bleach, but maybe it's better? I think it mostly removes the grey color and any mossfungus. Agree on the thick deck "paint" (actually called opaque stain). Good stuff.
 
The "deck cleaner" is a much more expensive form of bleach! It is not better, just more expensive. I do not know the cost of using pool bleach........ Yes, it mostly removes the grey color and moss/fungus. That is the purpose of cleaning the deck.

I like that foo foo dog too!
 
Back
Top