Docking problems

kindredspirits

Member
Member
Joined
Jun 28, 2007
RO Number
27052
Messages
263
This past weekend I had a problem at one of the docks we frequent and figured I'd ask for some advice. I've got a 26' boat with a single I/O. The transient slip I had a problem at required me to come down the row with boats on either side. I had to pass our finger slip(no pilings) and then reverse in and tie to port. I was alright with my stern but the wind took my bow and blew it over. I was able to apply power forward to port and correct the bow drift but it got me thinking about springlines and how maybe they would have prevented this. I've heard you talk about these before but can't envision how I would connect a line to the midship cleat and get it to a dock cleat while I'm trying to dock, especially on the port side. How do you do that? Any tips for backing into a dock like this with a single I/O would be greatly appreciated.
 
Here's a spring line animation...

entering_a_slip.gif
 
A few comments on the animation base on my boating experience. I am just throwing this out there to extend the conversation on how to use spring lines and not to kick dirt on anything here.

1. Most of the time the boats are sticking out past the poles or piers.
2. Would you need to forward spring line in this scenerio? I just saw it says it keeps the bow in place. I guess for a single engine.
3. How can you "lengthen" spring lines when backing down? Admiral? Sounds like a possible argument coming to me.
4. Do you risk getting pinned pulling up to the dock like that with the wind pushing you in that way?
 
That is a very cool illustration of docking.

I have a problem many times when trying to leave my dock and the wind is blowing hard against the starboard side of the boat. The wind is so strong that it pins the boat against the dock and makes it very difficult to move away from the dock. Any comments or illustrations for that?
 
I see what your talking about, but to tie to port do you spin 180 degrees and do the same procedure in the opposite direction? This slip was at the end of the dock. When you come in how do you get your docklines onto the cleats or do you rely on the dockhands to control the length? Thanks again for your help
 
Very easy solution, this problem was very simple for me when I had my 25ft single and it also works even better with my 31ft twins.
Try your best to get your stern close to the dock, throw a line to someone on the dock then switch off engines, sooner or later you will have your boat in the slip.

Trust me this will save you a fortune, with engines off the absolute worst damage you are going to do can probably be repaired with a a little rubbing compound and wax.
You will do a ton of damage to your boat and possibly someone elses if you use throttles to get out of trouble docking, maybe not the first time but it WILL happen.
 
Neal

if you are pinned alongside a dock, it's real easy. you put a spring line from your mid ship cleat (or bow), leading aft to the dock. about 1/2 length of you boat. put the sterndrive in forward and turn the wheel towards the dock. That will kick the stern out, when you're at a 45 deg angle, straighten out the drive and back out.

the last thing you want to do in that situation is try to leave bow first in forward, that's a sure way of banging the stern/swim platform in the dock.

obviously when springing off like that, you need to protect the bow. If you have wooden piling, you can just pivot the rubrail against the wood... if you are against a dock, all you have to do is put a couple of big fenders at the bow.

I use the same technique when pinned agaisnt a concrete bulkhead I often tie up to. for my boat, i use a couple of 18" balls. on a smaller boat you can obvoulsy use smaller fenders.

note taht this works well with twin engined boats, except that you dont' have to use a spring line. you put the offside engine in forward, rudders turned into the dock, and use the dockside engine, in reverse, as a spring line.

the animation above rarely works since you almost have boats sticking out beyond the pilings...

back to the original question, a spring line won't do you much good until you are at least partially into the slip. it will help keep the boat lined up but as you get in the bow can still get pushed by the wind.

what you want to do is secure a spring line from your midship or stern cleat to a piling or cleat as you back in, the line has to be long enough to let you back in some more. as it gets taught, it will keep the boat lined up.
springlinein2.gif


otherwise, the trick is to anticipate the wind and let it help you. for instance, if you're coming down the fairway to back into a slip on your port side and the winding is coming in the opposite direction, you need to overshoot the slip a little as you turn away to line up. Then when you start reversing the wind will push the bow as you back the stern in. the goal is to be lined up when your stern gets in.

windysingle.gif


I always turn the boat away from the slip as I come in to line it up before i back up. I find it easier to back up in a straight line than backing and turning at the same time. It's also easier to move the stern sideways if you're not perfectly lined by the time i'm in position 3 (second row)

the second method also makes it easier to anticipate the wind.
-If the wind is blowing from the right, I will overshoot the turn so that the boat is further right when it's in position 3.
-If the wind is blowing from the left, i will under shoot my turn so that the boat is further left in position 3.
- if the wind is blowing from the top, all i have to do is approach in 1 favoring the left (dock) side.
- if the wind is blowing from the bottom, I favor the right side knowing the wind will push me back into the slip.

backingcomp.gif
 
Pascal,
I see what you mean by using the line to guide the bow, but how can I connect that line to a floating finger pier cleat(no pilings)? When it's windy I'm not sure I could pry my hands off the wheel long enough to do anything else!!! I know it can be done, I'm just not sure how. When you come into a slip like this and feel the need to use springlines do you trust the dock hands to control there length? Controling there length while trying to work the throttle and steer at the same time could get complicated. Thanks again for all the help, so far I've been very lucky but I think I need a better way to control this boat in close quarters.
 
well, you have to accept the fact that sometimes the boat is going to be moved by the wind or current and set fenders accordingly to protect your boat and others if you drift a little. you can only have so much control over a boat...

when i need to pass a line around a cleat, from the boat, I use an extra long line and throw the bight of the line behind the cleat then pull it back and secure the bitter end on the cleat on the boat, same cleat as the eye. so the line does a round trip from my cleat, to the dock and back to the cleat. it's the quicklest and easiest way to secure a line on dock.

if there is a dock hand and i'm alone, then yes i will let them secure it although i will keep an eye on how long they set it. If that's the case, you may want to secure the bitter end on your boat, adjust the length as needed and jsut pass them the eye with instructions to just put the eye on the cleat.
 
Good stuff. What I've been curious about lately is what's going to happen to these folks that buy those fancy new "joy stick" systems if they ever have a problem. Do those systems still make it idiot-proof if they've lost a prop, or a shaft, or an engine? Don't get me wrong, they sound great, but I really hope we don't see more and more skippers in the next few years that have no clue how to manually dock a boat without their $50k crutch.
 
Another method would be to back in to the wind, you will have better control than having the wind pushing your bow around.Its something you have to get used to, it takes time to master a single screw boat, try and relax and if you screw up, just pull forward and try again. I found that using enogh power and knowing when to turn that screw the other way really helps.

One more thing, don't ever shut down your engines while docking, that would be the biggest mistake because then you have no power to go anywhere but were the wind will take you.

Last, if your still havng trouble and you dont want to mark up your boat, try asking a local Captain to give you some pointers and show you how its done. It may take the worry out of it for you. Good luck and keep practicing, after a while it will become second nature on how to do it.
 
I'm following what your saying...and I have been practicing..alot. In situations where I'm docking stern-to on the port side I try to leave enough room for my stern to shift to starboard in case I need to adjust my bow to port and vice-versa. Leaving enough room to move forward and correct my bow has saved me so far, I'm just very tense when docking this boat in situations like this. I'll practice with a spring line off my mid-cleat and see if that adds the safety factor I'm looking for. I've been working on my docking skills for 3 years now and still the wind catches me off guard at times. Maybe bow thrusters were designed for people like me, but on a 26' boat????? From what I've read I need more practice, not a bow thruster---correct?
 
There are some days and some situations where you just have to pull up to the finger pier, shut her down and walk the boat into the dock! I did that a few times with the 250 DA because the slip was tight, the wind was howling and the fenders just weren't big enough. It's great if you can dock under extreme conditions, but sometimes it's easier to throw in the towel and take the easy way out! That's when really long dock lines are your friend! Spring lines work great and make you look like a pro, but you need some assistance to get them set while the boat is drifting or while you are holding it close to the dock under power. Just remember you're the captain and having a plan that is communicated to the crew (even yourself!) is half the battle sometimes.
 
"It's great if you can dock under extreme conditions, but sometimes it's easier to throw in the towel and take the easy way out! "

It's a darn sight safer (and cheaper) too!... Know your (and your crew's) limitations.

In a real pinch I've had drop an anchor; used right it's almost as good as a spring or a bow line but doesn't require a piling. The trick is getting it back once I'm alongside. Sometimes I can't, and have to leave it in the mud till the weather improves.
 
Most boats at our marina extend beyond their fingers. We have no pilings out front to pivot on. Our slips are pretty tight. When you're single handing a 30 footish cruiser in adverse wind/current conditions and there is no other help available (pretty common during the week), using a spring line is darn near impossible to help get you in because you can't get close enough to the cleat to set the line. I dock with my starboard side to the finger and I have no slip mate at this time. In adverse conditions (mostly wind) I run two lines from my starboard midship cleat, one to the back of the boat (along with the stern line) and one up next to me at the helm.
I can usually get the stern far enough in so I can quickly get to the swim platform and then to the finger with both stern and mid cleat lines already in hand. From this point I can walk the boat the rest of the way in before the bow can get too much out of control. If someone should be around to assist, I have that second mid cleat line at the helm to throw. It would be great to have pilings between every slip to pivot on or be able to tee up to the end of you finger where setting a spring line would be easy, but in many marinas that is simply not the case and you do what you need to do to get in safely and prevent damage to your boat, your neighbor's boat, or the dock.
 
A few thoughts on the recommendations here:

Billybo "throw a line to someone on the dock then switch off engines, sooner or later you will have your boat in the slip" I'm against shutting down the engines until I'm secured especially if there are adverse conditions. You never now if you need to bail yourself out. Also, putting a lot of faith on the person on the docks who now has total control of your destiny.

JohnH "I can usually get the stern far enough in so I can quickly get to the swim platform and then to the finger with both stern and mid cleat lines already in hand" Again I would be concerned about leaving the boat before it was secured. What if you slipped and dropped the lines....oh sh!t. Maybe it's just me and I'm paranoid but I would rather struggle with catching a cleat from the boat than leaving the boat before it was secured.
 
interj,
I understand where you're coming from, but I won't jump from the swim platform to the finger. If I can't easily step from the swim platform to the finger, I'll not attempt it, I'll maneuver until it's an easy transition. I do agree that the engines should not be shut down until the boat is secured. Maybe I'll experiment with using a boat hook to secure a spring line to the forward cleat of the finger, but when single handing that may not be so easy either.
 
in your home slip, you are better off leaving the lines so that you can jsut grab them coming back in... much easier that at a transient slip where you will have to secure the lines ashore.

just leave the lines in a way that you can grab them or use a hook. With an express you're not to far from the cockpit so as your stern comes in, you can quickly grab the spring line, tie it to your aft cleat and go back to the helm. then as you back in and put tension on the spring the boat will stay along side the finger.
 
Along what Pascal says, what I did with our 26' (single) and now our 30' (twins) is I have leave the lines on the dock too - I have a separate set of lines that stay on the boat to be used when away from our "home" slip.

I have a piece of green yarn thru my "spring" lines (to show which ones they are) so as I back into my slip whether it's me alone or if there's a dock helper, if they put on the spring lines first my boat will only go back so far and then those lines will help pull/swing the boat towards the finger pier.

I back into our slip . . . when I single hand the boat, I get into the slip. Put the drives into neutral. Grab my boat hook and walk onto the platform and grab and cleat the stern springline. Then I get off the boat and walk down the finger pier to secure the other spring line - using the boat hook IF the bow starts to blow away from the finger pier.
 
That animation in the first reply is great, But a bit easier way to do that is to use a "running spring line" where you use one long line that you attach at the bow and stern that you just put over or around the piling and it self adjusts as you back in. (No yelling at the Admiral to adjust it. :-)) Then once in the slip you replace it with a bow and spring line.

"Very easy solution, this problem was very simple for me when I had my 25ft single and it also works even better with my 31ft twins.
Try your best to get your stern close to the dock, throw a line to someone on the dock then switch off engines, sooner or later you will have your boat in the slip."

This is very bad advice on many levels.
 
Back
Top