Epoxy tecniques?

Thudpucker

Active member
Member
Joined
Oct 20, 2002
RO Number
10503
Messages
3,677
I've had some sour luck with those 5-minute Epoxy's.
On larger volumes of work, using real Epoxy, part "A" and "B", how do you guys do it?

I've heard war stories about the Pumps. Good things about disposable Dixie cups etc, medical cups, Syringes for micro-measuring and digital scales for weighing as opposed to the various volume measuring.

I don't use a lot of it. In between uses the cans sit down in the Barn, heat and cold.

Tell me (us) about what you do that works!
 
I've been working with epoxy for many years now and with excellent results. The products I've been using the most have been West System, MAS and System 3.

I've never had alot of luck with the pumps due to air bubbles, etc. I've alway used the volume measuring cups. One ounce cups for small jobs to quart containers for larger. Unlike polyester resin, epoxy must be mixed at the exact ratio for best results. Measure carefully. Mix very well. Never thin epoxy. Just thinning 5% can reduces it's strenght by 30% or more. Heat it up instead. If I need it to really flow I'll heat it up in the microwave to about 105 degrees. Then it's as thin as water.

I've used to building my own boats, model airplanes, replacing rotted coring on decks, replacing stringers, barrier coating of the hull, etc.

k3.jpg


Dave
 
On medium size spot work I use some of those restaurant supply ketchup and mustard squeeze bottles. I put my resin in about 3/4 full and add hardener by drops, more hardner drops give a quicker set and a little less gives more time. I just shake up the the mixture and cut the size hole I want. On larger jobs I use the quart size plastic paint containers available at the chain homedepot type places. Again I mix by how fast I want the mixture to set and it seems to work for me. For thinner soaking mixtures like an intial coat on a large piec of plywood I've added about 10% acetone for a thinning liquid to make a thin soak-in spread. I've never mixed more than a quart at a time, never used any of the pump apparatus either. I'm sure there are more professional methods and of course your mileage may vary.
 
I've tried pretty much all the major brands and I've settled on Tap Plastics for a number of reasons. You get a true gallon per gallon or Qt per Qt size and the mixing ratio comes in full sizes...RE 1 gallon resin for 1/2 gallon hardener containers. Not partially filled containers like most of them. AND the price is better. I also get a commercial discount because I've been buying from them for so many years.

Tap Plastics also has the lowest amine(waxy substance that rises to the surface) so it doesn't interfere with or require cleaning on second or added coats or when filling corners after the joint bond.

Dave pretty much has the correct application techniques, I would only add that painting a thin coat of straight epoxy to raw wood, especially end grain, and letting it soak in will prevent starved joints...but don't over apply because you will dilute the mixture of whatever thickeners in your mix. Also, use the cold/long cure formula. It has the least amine blush and strongest bond and longest work time.

...and I haven't used them pumps in over 15 years. yeach! I DO use them for pumping drive fluid or even differential oil in cars. They pump 5-10 times the volume per pump than the drive oil pumps.
 
Great ideas.
I've often wondered how to 'thin' epoxy without adding Acetone or Alcohol. Heating it sounds like it will work similar to CPES.

When you heat it to 100 degrees, does that cut down the time you have to use it?
I'm assuming your going to seal a piece of plywood. You'd heat the stuff, pour it out onto the plywood and start rolling immediately.
As a for-instance, would you get a quart to roll out on a 4X8 sheet in time or would it start to gell before you got it all out to the corners?

Crossroads, the Ketchup n' Mustard containers have been used by other guys too. I just saw it in the last two days though.

So far, I'm leaning toward pumping into a "Marked" container for exact mix.
 
quote:

Originally posted by Crossroads

On medium size spot work I use some of those restaurant supply ketchup and mustard squeeze bottles. I put my resin in about 3/4 full and add hardener by drops, more hardner drops give a quicker set and a little less gives more time. I just shake up the the mixture and cut the size hole I want. On larger jobs I use the quart size plastic paint containers available at the chain homedepot type places. Again I mix by how fast I want the mixture to set and it seems to work for me. For thinner soaking mixtures like an intial coat on a large piec of plywood I've added about 10% acetone for a thinning liquid to make a thin soak-in spread. I've never mixed more than a quart at a time, never used any of the pump apparatus either. I'm sure there are more professional methods and of course your mileage may vary.






This works for RESIN, but not for EPOXY. Be careful. Doing this will EPOXY will ruin your repair.

For small repairs, I like the Hysol products available through McMaster. Get the applicator and tube. Mixing and application is clean and easy. For larger repairs, West Systems is readily available works well.
 
Please rembember that epoxy and polyester are different products. Adding more or less harder to epoxy does NOT result in a quicker or slower cure rate. Just a weaker final product. Epoxy must be mixed at the exact ratio for the strongest cure. Cure times can be controled with different harders or tempature. Polyester cure times can be controled by harderer ratios.

"When you heat it to 100 degrees, does that cut down the time you have to use it?"
Yes it will. If you need more time use a slower set epoxy. Always mix well scraping the sides and bottom of your container.

"I'm assuming your going to seal a piece of plywood. You'd heat the stuff, pour it out onto the plywood and start rolling immediately."

Correct

"As a for-instance, would you get a quart to roll out on a 4X8 sheet in time or would it start to gell before you got it all out to the corners?"

Just be sure you use a slow cure harderer such as West system 106 or as I've done lately using System 3 using either their medium #2 or slow harderer #3. Gives you plenty of time even when heated. Just takes about 48 hours before it's really hard. I'm also sure there are other epoxy systems out there that are just as good. I just haven't tried them.

Dave
 
quote:

Originally posted by Wingspar

I've been working with epoxy for many years now and with excellent results. The products I've been using the most have been West System, MAS and System 3.

I've never had alot of luck with the pumps due to air bubbles, etc. I've alway used the volume measuring cups. One ounce cups for small jobs to quart containers for larger. Unlike polyester resin, epoxy must be mixed at the exact ratio for best results. Measure carefully. Mix very well. Never thin epoxy. Just thinning 5% can reduces it's strenght by 30% or more. Heat it up instead. If I need it to really flow I'll heat it up in the microwave to about 105 degrees. Then it's as thin as water.

I've used to building my own boats, model airplanes, replacing rotted coring on decks, replacing stringers, barrier coating of the hull, etc.

k3.jpg


Dave






+1 but Dave's kayak is way more a looker than my pygmy. I am so jealous!

I have used pumps before on a larger scale blister job. So long as the pumps are primed and used frequently, they work well. I don't like them for mixing small amounts and prefer volume mixing in the plastic and marked tubs. I bought a dozen or so and after the are all mucked up, I go back and flex the cured epoxy out, clean them up and recycle them back into the lineup.

As already mentioned, be VERY careful about what you did to mix different brands and products and how they cured in different situations. Haze, amine blush, color, fast hardener, slow hardener etc.. While its easy to mix up polyester and epoxy resin techniques over time, its absolutely unacceptable to hand out the wrong advice on a forum which could cause someone to go through absolute hell because of it. A false or incomplete cure is something you want to avoid at all costs.

Might I suggest keeping a journal on your product and mixing combinations over time? Then record the cure results along with ambient temps and such. I wish I had.
 
For measuring, esp for "medium" size projects, those pre-marked measuring cups get expensive...

Find some clear plastic disposable beverage cups ( NOT wax! ) Place one inside another, then pour a measured amount of water inside the inner cup. Carefully mark the level on the outside cup.

Now discard the inner cup ( or air dry it ). Keep the marked cup.

Mark one cup each for the part "A" and part "B" liquids.

To measure resin, place a fresh clean cup into the marked reference cup. fill the inner cup with resin, so the the mensicus meets the line. Then use the inner cup and discard after use... Use the same marked cup for the entire operation,

This allows you to use the unmarked, inner cups ( cheap ) and still obtain a reliable measurement.
 
For what it's worth, and no I don't post here much, I just finished replacing my stringers and sole in a 22' cuddy using marine ply, biaxial fabric and 10 gallons of West Systems epoxy. I used the pumps and didn't have one bad batch. I usually added a filler so that it would stay put. Colloidal silica worked well for me. Try it, you'll like it.
 
Back
Top