Ice maker craped out

Captain Crunch

Member
exMember
Joined
Oct 17, 2001
RO Number
6460
Messages
85
Went to the boat yesterday in 35 degree weather only to find my ice maker was not making ice, instead generating heat in the box. the cube unit in the box is actually luke warm and the melted ice is warm water. the Ice maker is a U-line BI 95 model. Anyone experience this and can it be serviced or will it need to be replaced entirely.

tks
cc
 
CC try posting that in the Marine sanitation/head plumbing section. We have Raritan's best on there Vic William he also understands U line ice makers.
Bill
 
Oh Jeeze, Thats the end. Quick, sell the boat before something not as important goes bad next.
 
It could be due to the cold outside temperature

A common question we hear pertains to operating a refrigerator in the garage or other unheated space during cold weather. Bottom line, refrigerators and freezers don't cool efficeintly when operated at temperatures below, roughly, 45 degrees (F). The first reason is that the outside temperature may get low enough that the thermostat inside the refrigerator never gets warm enough to activate the compressor and so the freezer warms up to the outside temperature. Another problem is that if it gets too cold, the refrigerant pressure becomes too low to generate the necessary cold and so the freezer only chills down to the outside temperature.

http://www.acmehowto.com/howto/appliance/refrigerator/overview.php
 
Probably something to do with the switches that cycle stuck in the harvest mode. Vic can explain it better than I can.
 
Thanks Hogan...I always wondered about that. Great info.
 
Go to the forum "Marine Sanitation & Plumbing" there you will find Vic Williams & all you could ever want to know about U Line Ice Makers.
 
Hogan, Bill,
Thanks! I'm going back down today to do some troubleshooting and will post more in the sanitation forum with Vic if necessary.

tom
 
check the fan.... i've had a couple of those over priced POS Uline stop working because the garbage grade made in china $0.89 fan craps out...

Uline has to be the worst marine equipment on the market... they are worthless!

... i feel better...
 
Pascal,
After looking inside this unit I would agree its a POS. Can't get to the fan without pulling the unit, but it did run for 1 minute when powered on before shutting down. I'v posted in the sanitation forum with vic, but leaning toward replacing with a better quality unit. by the way, the fans in your computer are probably from China, but they cost a bit more that $.89....lol.
 
i've seen the Uline Fridge/Icemaker combo unit rust out in protected location after just a few years... for the kinf of money Uline charges, you'd think they'd use stainless steel... and the damn thing only makes ice if you crank the Tstat off, but then the dirnks in the fridge portion freeze up... and then after a few days, the ices becomes a useless solid block.

i hate those things, unfortunately i dont' know what else is there....
 
Ditto on U Line being a overpriced POS. I ordered a new door for mine, installed it and there is a 1/16" crack all along the bottom of the magnetic door seal, and NO adjustment (for the bottom hinge). Hate it when I have to tweak under engineered over priced stuff. Reminds me of american cars from the 70's and 80's. Is there a lesson to be learned here ?
 
CC-bring a com[pressed air source with you and blow all the dust outof the unit that you can. That may help.
 
Pascal,
for the ice maker, Raritan appears to have a drop in replacement. A bit pricy, but, looks of much better quality,,,stainless steel etc.

U-Line service tech response:
If its not to old you can find it behind the ice bucket. If the unit is not cooling the question would be is the compressor and fan running? If not then where is the ejector blade at.It should be pointing at 12 o'clock position.If it is and nothing running then it could be the thermostat. If the compressor and fan is running and not getting cool then it could be the sealed system. Either a leak or a bad compressor.
Thank you

U-line service seems to be very responsive at this point. I'm going to check this ejector blade position, but, don't think I'll put any money into this unit.
cc
 
Here's my thoughts so far. I bought a new door because the old one was UV deterierated, about a hundred bucks. Then I bought a new complete mechanism (the mechanical part inside that actually makes the cubes) about $165.00. Now if the boat had never had an ice maker it wouldn't matter. But since it did. . . . .then I want it to work. And I think they are around 8 or $900.00 overpriced bucks. So I feel like I got a bargain comparitively speaking.

And just a FYI. When I opened the well packed mechanism, it had been damaged. So I had to tweak it and re use a plastic piece from the old unit. And the decal on the front of the cuber had been applied side goggled, I was able to peel it and re glue it squarely . POS new, POS replacement parts. What can I say ?
 
Back
Top