Pascal on the move

I'm tempted to say that's just when you need it to keep holding and you get what you pay for. ;-)

But for God's man, at least use a different swivel! :-)

(One day we have to do this over drinks.)
 
Great fun watching your cruise Pascal .... motivating me to keep my project boat moving forward. Keep up the good work!
 
On your way through Norfolk give us a horn blast... we are anchored between Hospital Point and Tidewater. Waiting for charts we had to order before heading south. You can't miss us, we are the only powerboat in the anchorage :-)
 
Charmer/Pascal sighting this AM: ICW Mile 752 30-12N 081-24.5W
 
hey J-D, nice chatting with you this morning!

Pale Ale, will do although i hope you get your charts by the time i get there! i usually refuel at Portsmouth boating center, good priced fuel there
 
Just might make it back in time to wave as you go by.. Just finished up the trip north with a 76' Lazzarra.. Heading home from Erie today.. Hope you have the same weather windows we did..
 
quote:

Originally posted by jrpar

Just might make it back in time to wave as you go by.. Just finished up the trip north with a 76' Lazzarra.. Heading home from Erie today.. Hope you have the same weather windows we did..






John, nope, he's already blown through here. Looks like he anchored just north of Fernandina Inlet last night.

Hope the trip with the Lazz went well. Was that the one docked at PC MArina?

Bob
 
Paper charts will be here Tuesday, the C-Map chip Wednesday or Thursday... so we'll be here for at least another week.

fyi, we met briefly in Annapolis. We were at Pussers when you came in and tied up in Ego Ally. We walked over and introduced ourselves and you gave us a quick tour of Charmer. I am nondescript, my wife is an attractive tall thin redhead :)
 
Looks like he went out Fernandina Inlet and running outside. From what I found last month in the ICW in GA and SC that's a good move.

Plus, from the looks of it he has some fantastic weather to run in. I'm envious!

Bob
 
Pale ale ... Of course! Now I remember!

Bob. Georgia isnt bad when high tide is around mid day but right now it s late afternoon and it s just too hard to make it work without loosing a couple of days.

Passing 12 nm off st simmons, will anchor in port royal tonight. Can't wait to pick up a replacement claw in Oriental! The spare 60 lbs SS danforth has less than half the holding power! It held fine in the current last night and the night before but mostly because I used a lot of chain
 
Pascal, you probably already know this, but, after you enter Port Royal Sound, right at the north end of Parris island there is a creek off to the left. (On the chart it is the Port Royal Reach. The entrance is at "G 41") At the entrance, on the north side of the creek, you will see an old industrial dock complex that is, for the most part abandoned with a turning basin with good depth. Just past that, also on the north side of the creek you will see a dock sith a few commercial fishing boats tied up.

There is a restaurant there called Dockside. It is excellent. Well worth a dink trip to have dinner.

Bob
 
thanks bob... not a good night for a dink ride considering the weather!

it was somewhat of a rough arrival in Port Royal, i was going to anchor in Cowen Creek before port royal when i realized that there was a massive line of TS building to the NW and much closer than it looked. and i dont' trust that spare anchor...

I made it to the Port Royal Landing marina jsut as the first gusts were starting to pick up... today was one of the rare time that i was glad to have the bow thruster so that i could slow the boat down (bow thruster plus splitting the gears...) since the wind was blowing hard on the dock.

by the time i had the boat tied up i was soaked!
 
Is the current as bad at Port Royal Landing as it is at Beaufort Downtown?

Bob
 
it's about the same, it's a little wider here so may be a little better. as long as you can come in into the current it's not too bad.
 
quote:

Originally posted by pdecat

is there a story in the missing anchor?






His, what appears to be to me at least, Suncor brand swivel failed. As two almost did on me several years ago.

SuncorSwivel.jpg


I can't speak for Pascal but I highly recommend anybody using one of these swivels for anything but perhaps a lunch hook consider switching to something else ASAP.

Suncor does appear to be making some more HD swivels now.

AnchorSwivel.jpg
 
I missed that. I have always used the galvanized type I figure thqt I can see the rust when it starts but I always expected the bolt to fail not the part that you can see.

Pascal So that I dont misunderstand that was a Bruce copy?? China?? I may try one next as my expensive delta brand has rusted badly.
 
Back
Top