Phoenix 37 Convertible

Britanic

Member
Member
Joined
Jul 18, 2007
RO Number
27562
Messages
985
Got my eye on a 1990 w/6v71's. Looks clean. Any info on these? Good, bad and ugly please.
 
Based on the information that describes this boat, you mean 485HP 6-71TIBs, not 6V71s. GM did manufacture a 6V71 configuration, but it was not that good of an engine and was subsequently dropped from the line.

With 600 hours use, is that only 600 hours total time, or is it 600 hours SMOH?
 
Yes Bill, thats the one. I dont know about the hours, I will be looking at Her this weekend. I am looking for common defects with this manufacture / model as I am not familiar with it. Such as common stress cracks, coring issues, leaks etc. As with my current boat, any vessel of this age that has been properly maintained probably has had these "common" issues repaired, the repair is what I will be looking for.

In regards to the yachtrworld add - cruise speed is said to be 27kts, not bad in my opion. We are looking for a convertible with two staterooms, diesels and a aft positioned helm on the bridge. We seem to like the layout of this (as compared to Luhrs, Egg Harbor, Silverton etc) that we have looked at, and the price seems right.

The boat has prop pockets, anyone have pros and cons aside from shallower draft? We use our current boat often (every weekend in Jersey) and mostly cruise, or hang at anchorages. Occasional fish 5 to 10 miles out...
 
The sometimes controversial, but always worth listening to David Pascoe has generally nice things to say about Phoenix boats and the way they were built; rare for him. I have no direct experience with them myself.

485 HP out of 6-71s is really a lot, you'd want to get a top notch Detroit surveyor to analyze them thoroughly.

In general, prop pockets can cause boats to be a little harder to handle at slow speed, tending to wander rather than go straight, and coming up to planing speed with a more severe upward trim. These would be things to watch for in a sea trial.

George
 
If I remember correctly, Phoenix and Blackfin share some heritage together. I don't recall the specifics but remember that somehow they they both had something in common. At one time I think one of the owners of Blackfin came from Bertram and maybe had something to do with Phoenix.

Others might remember the whole story better than this.

Nice looking boat, looks like a very capable fishing boat.
 
quote:

Originally posted by Robyns Nest

If I remember correctly, Phoenix and Blackfin share some heritage together. I don't recall the specifics but remember that somehow they they both had something in common. At one time I think one of the owners of Blackfin came from Bertram and maybe had something to do with Phoenix.

Others might remember the whole story better than this.

Nice looking boat, looks like a very capable fishing boat.

The prop pockets will also have an effect on backing down as the full flow of water just isn't available to the props like a straight bottomed hull.




 
I had a 1982 29' Phoenix Sportfish. This boat was built like a Sherman Tank. Very well designed, strong, well laid out. I never noticed an effect of the prop pockets when backing down, she handled well and the pockets allowed me to go places I wouldn't have been able otherwise. If I didn't need more room, I'd still have her today. In fact the guy who bought her from me had her repowered with twin diesels. A great hull.
 
You might check in with Frank Piedra of Phoenix Yacht Sales in Miami, as he used to make them.
 
Survey those engines!! Parts for those older two stroke DD's are becoming hard to come by. Typical rebuilds per cylinder can be in the neighborhood of $5000/cylinder. Do your homework!

Doug
 
quote:

Parts for those older two stroke DD's are becoming hard to come by. Typical rebuilds per cylinder can be in the neighborhood of $5000/cylinder.




douglee-
I'm not saying that you are wrong, but are you sure about your parts assertion? And are typical rebuilds that expensive now?
 
quote:

Originally posted by Bill 2


quote:

Parts for those older two stroke DD's are becoming hard to come by. Typical rebuilds per cylinder can be in the neighborhood of $5000/cylinder.




douglee-
I'm not saying that you are wrong, but are you sure about your parts assertion? And are typical rebuilds that expensive now?









By the time labor is factored in, I'm pretty sure it's about that cost. Previous pricing was probably in the $1000-$2000/hole area. Call around and double check.

Doug
 
Boat next to me is a 1978 35 Bert with 555 cummins. No hour meter but original 30 year old engines, never overhauled. He estimates 3000 hours...was quoted $70K for replacements this year...did not say whether new or rebuilds'
 
Some of the Detroit parts are just slow to get, not impossible to get. You can get them but have to wait for the supply chain to catch up.

There are aftermarket suppliers for many of the parts like cylinder kits, heads, etc... but some of the parts like exhaust manifolds, blowers, turbos, you might be waiting weeks for your local DD dealer to deliver them.

The days of $2000-2500 per hole rebuild cost are gone.
 
It's gotta be worth while to repower instead now.
 
Back
Top