Rogue Wifi installation

walterv

Moderator
Member
Joined
Jan 11, 2004
RO Number
12640
Messages
6,381
I am thinking of installing the antenna in the bridge area on a rail. My enclosure is mostly isinglass with a fiberglass hardtop.

I will check signal before I run wires and the fiberglass antenna will be in full view of the isinglass.

So my questions are this:

Will the isinglass block reception?
And what if any affect will the hardtop have?

Thanks

Walter
 
Fiberglass and the tubes supporting the hardtop will affect the performance Walter. A good test is just try it as a temporary installation. This is real easy with the ROUGE just use a longer CAT5 cable. It all depends on the distance you want. To maximize performance I recommend mounting the antenna on the hardtop my secondary recommendation would be on the arch away from the radar and GPS antenna. You could always use an extension to get the WiFi antenna above the hardtop using a rail mount. My Omni is mounted forward of my hardtop's AC unit and above it My High Power unit is mounted within 3 feet of the antennas base minimizing cable losses from there it's about a 50 foot CAT5 to the Salon. The top 12' of the antenna is where most of the signal emulates.
Bill
 
Walter,
Isinglass shouldn't be an issue and you can probably shoot thru fiberglass. Bill has it right, test it before you mount it. Density/composition of the object that it will either defeat, absorb or deflect the radio signal. Something like fiberglass can probably be penetrated, you may need to go with a higher gain access point if your test fails or delivers too weak of a signal.
Perry
 
it's hard to test though, the difference may not be easily visible with the number of bars on the network scan screen, yet you may get slower speeds. in addition to the possible loss, being a few feet lower may further weaken the signal because of other boats.

mounting the external antenna on your arch is really your best bet and with Cat 5 cable there are no loss issue due to the longer run.
 
Since WiFi is a dynamic changing environment what works at the dock can be totally different when you are on the hook Walter. Did you get the boat's distribution access point worked out? Since switching to the 802.11A standrad I can now connect (at slow data rates) to Hot Spots with only one bar now. My unit is the highest end unit, I removed the internal 200mwatt re-distribution AP card and installed a 802.11A router 4 port switch at the end of the CAT5 cable from the bridge. I am very impressed with the improvement it made in my ability to access distant AP/Hot Spots.
In fact I'm on it now.
Bill
 
My next test is to get a cross polarized omni for the boat. I am also going to experiment with cross polarization on my installed high power AP's. I believe this will provide significant improvement to the overall performance.
Bill
 
Billy,
I need time to digest what you say, need more time to cross reference what you say and fold it into what I know. In other words, I like to understand what I do and why I do it. to say I am so into this is an understatement. :)

antenna3.jpg


antenna2bridge.jpg
antennaoutsideview.jpg


antenna2bridge.jpg


antennaoutsideview.jpg


After hours of testing the signal stength on 3 hotspots was no different from where I mounted the anttena than that of having it outside on the arch.
I bought a LinkSys/Cisco 2.4 g /5G router... My old laptop does not support 5G. Running 2.4 G runs fine on a N router.

I am running a VOIP phone as well as internet, next gig (next week) is installing cameras on the boat that works off the WIFI.

You have been a great help, thanks
Walter

PS,
I am on the boat now
 
Walter as long as you keep the power down on the N router you should be ok also keep it as isolated as you can from the ROGUE's antenna.
Bill
 
Here is a copy and paste of my connection page. They go from strongest to weakest available AP's (28 visable). Since I can not display the signal strength bars the top 3 are all green the next 10 are yellow the balance are red. I can connect to the weakest open network on the
list but the through_put (data rate) is slow.
The AP named Wireless Two is my Ericsson W35 set to 0dbm (it's lowest power setting) until I install a QOS router then the 2.4 WiFi will be turned off and distributed out of the QOS router into my 802.11A AP/switch.
Bill

Network Scan
Availability of public wireless LAN access points may be limited. The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed. Wireless connectivity and some features (i.e. VoIP) may require you to purchase additional software, external hardware or services.

Network ? Connected ? Have IP ? Internet ? Encryption ? Signal Strength ?

Hot Spot-Total Marine NO NO NO none Weak Strong

Tuckerton Beach Grille NO NO NO WPA Weak Strong

My Home Network NO NO NO WPA2 Weak Strong

08FX07007053 NO NO NO WEP Weak Strong

NETGEAR NO NO NO none Weak Strong

Sams Network YES YES YES none Weak Strong

Jolly Rancher NO NO NO WPA2 Weak Strong

WirelessTwo NO NO NO none Weak Strong

dlink NO NO NO WEP Weak Strong

hpsetup NO NO NO none Weak Strong

00:0F:B5:29:E3:BC NO NO NO none Weak Strong

NETGEAR NO NO NO WPA Weak Strong

Razzinet NO NO NO none Weak Strong

thleh NO NO NO WEP Weak Strong

chesapeake NO NO NO WPA Weak Strong

TOAD NO NO NO none Weak Strong

linksys NO NO NO none Weak Strong

star NO NO NO WEP Weak Strong

ANN-PC_Network NO NO NO WPA Weak Strong

116 Marlin NO NO NO WPA2 Weak Strong

00:23:69:AA:70:01 NO NO NO none Weak Strong

04B412741711 NO NO NO none Weak Strong

print server 2B786D NO NO NO none Weak Strong

linksys NO NO NO none Weak Strong

PAM-PC_Network NO NO NO WPA Weak Strong

linksys NO NO NO none Weak Strong

09FX01056525 NO NO NO WEP Weak Strong

08FX07010731 NO NO NO WEP Weak Strong
 
Back
Top