Rub Rail Removal

hamster

Member
Joined
Nov 1, 2007
RO Number
28887
Messages
88
I have a 2005 2665 Regal that has a small leak in the starboard side of the salon. It doesn't leak all the time but when it does, it drips down behind the back of the backrest and down into the storage area under the seat. The most we ever had was about a cup full. It appears like it's inline with the rub rail. How difficult is it to remove the rub rail and recaulk it. And, which caulk is best for this job.
Thanks,

Joe
WaterLeak.jpg
 
Removal of rub rail - easy

Installation of new rub rail - depends on type of rub rail being installed and can be fairly straight forward to a down right PITA.

As for which sealant to use, opinions vary widely on this. I have seen anything from silicone sealant to 3m 5200 used. Personally I follow the manufacturers recommendation.

A few tips for you.

Do this with a helper and on the hottest day possible. Let the rub rail sit in the hot sun on hot asphalt before installing. The boat should be warm as well. Do not measure the old rub rail for the size of the new one - it has without a doubt shrunk.
 
as usual, not a particularly difficult job but not too much fun either. have you localized the leak or are you wanting to do the whole boat? i've only done an entire boat, not sure if you can do a section and get it back successfully.

either way, you've got an insert and a rail. the insert needs to be pulled to reveal the screws attaching the rail. depending on whether you have SS or rubber, there is at least 1 seam somewhere for the rubber, SS should have smaller sections i would imagine. there's a video on you tube, search taco marine rub rail.

3m 4200 lists rub rail installation on the label. there are others i'm sure. the warmer the day the better when dealing with rub rails.

edit...ITK beat me to it, i'll add that rub rails scratch REAL easy. laying it in the sun is good but be careful.
 
In the know has obviously done a rub rail in the past. haha I would also look at the screws holding the rub rail to the boat. I have seen the screws actually push or seperate the boat cap from the hull under the rub rail. This will cause water to leak into the boat while under way. This could explain why it leaks just sometimes. Maybe someone can explain this a liitle better than me. Good Luck!
quote:

Originally posted by hamster




 
I hope your manufacturer was more conscientious than searay. I found a very POOR attempt to pop-rivet the deck to the hull. Many places the holes didn't even line up or the sides were too far apart to pull together. Piss poor construction.

5200 need a very clean and hard surface to bond and seal. Just squeezing it with a caulking gun without getting rid of any dust/dirt/mold or other surface contamination will give you a leaky repair.

I tried 3 times before getting a successful job. Trying to repair a section at a time just might allow water to travel to another area where it will leak.

I hope you luck.
 
Thanks for the responses. It's not a big deal and not to sure if I want to take on the challenge. I hope it's covered by the extended warranty I took when I bought the boat.
 
Also check the bow rail.You could remove one screw at a time inject caulk into hole, reinsert screw. Do this for bow rail and rub rail. Could be better than replacing the rub rail. Water can migrate from a distance. The leak is not always where it seems.
 
Covered by warranty??? Doubt it. Don't start removing "screws" from your bow rails or anything else until you know what's behind them. I doubt you have screws holding bow rails etc. They should all be thru bolted with backing plates and nuts.
 
I removed the rub rails from our '78 Trojan just to paint them. In addition to new stainless hardware, I used 4200 or 5200, can't remember which...
 
Back
Top