Smart Craft Help Needed.

David M

Active member
Member
Joined
Mar 5, 2005
RO Number
16492
Messages
7,393
Saint Max is equipped with 2007 6.2L Smart Craft ready engines. I have looked and looked and aside from Merc pimping their own product, I can't find anything about it. The local dealers are almost as clueless as I.

Pros and cons please. Is it worth even messing
with?

TIA. Any and all input welcome.
 
So, what exactly do you have (in terms of SC gauges), and what are you considering doing / adding?
 
That's just it. I have none. Apparently, the SC engines have analog output as well. I have all the original gauges and don't know where to start. Fuel flow / MPG is my main concern, however, I know there is an quasi engine sync module in the System View (?) panel via digital tachs but nobody around here knows if the tachs display digits in increments of 10 RPMs, or 1 RPM. That may sound small, but in theory, it could put me off by as much as 19 RPM.

What other diagnostics and prognostics are available via SC.

Are there plans for a conversion box to translate the SC language to NEMA 2000? If so, that effects other equipment choices.

I'm flying blind here.

TIA for all posts.
 
I bought a smartcraft monitor from boatfix last year. Depending on the sensors that your engine installer included you can get a lot of info or just a little. There are several different levels of gauges depending on what you want to know. http://northamerica.mercurymarine.c...tataglance/components/information_display.php will get you started on what each of the types of gauges are capable of showing. There are links from there that tell what each engine should be prewired for, but keep in mind that it may be less.

As for diagnostics, I get Water Pressure, Fuel Water Separator status, Oil Pressure and temperature, Engine Temperature, Battery Voltage, Fuel Flow/ Level/ Range (mine is within 5% when I fuel up). It sets off an alarm if the engine itself detects anything out of spec. In my case last month it told me that my water pump failed. It really didn't, it was the sensor that went bad, but it was still useful as it made me aware of a potentially expensive repair and I nursed the engine home.
 
I have the same setup,in fact I bought new and on purpose did not get Smartcraft Option installed from the factory. I wanted the look of analog guages, and knew I could spend $400 total and get the harness and two small electronic gauges I needed.

I get GPH, Total fuel used (great cause tank gauges are normally way off), plus all the redundant info like oil temp, water temp, trim position, etc.

For me it was the best $400 gadget I ever bought...
 
Also, I did a ton of research on SC to NEMA 2000, in my opinion it may never happen. Technically it is possible, but too much compeitition and Merc likes to keep that line of business. My E80 is all plug and play for NEMA 2000, and it can repeat all the info coming from he engines, just will NOT work with SC, so I had to by the Merc Gauges...

Maybe in 5 years this might change, and Maybe someone else has more insight, but I would forget about it for now.
 
I use 2 System View 5000 displays at the helm, they are both set up to monitor both engines on the same screen (oil pressure, water temps, voltage, circulating pressure) is an example of one of the engine screens. I use one to watch the engines and the second to either syncronize the motors or watch my fuel flow/ burn rate and range as well as the gas tank level. I can and do monitor my Kohler generator, and various tank levels as well. I could have done the AC units because they were smart craft ready as well but decided not to since they rarely run when we are cruising. Regards Bill
 
Are the sensors add ons or are they in a module somewhere already on the engine?

toofast: What does your set up consist of for $400. Is it the tack with the little screen in the bottom?

Billy: If I may ask, how much were the System View 5000 per engine?
 
We have the smart craft system with twin merc outboards. In my opinion, more hassle than its worth, but neat nonetheless. There are different "Groups" or icons for the different functions you want to look at. For example to pull up Engine RPMs, speed, oil pressure, water pressure, and temperature, you select a certain icon. There are different screens to scroll through and one shows engine RPMs and a synchronizer, another shows RPMs and speed, another shows water pressure and temperature, another shows oil pressure etc. So you have to scroll through the screens to find what you are looking for which to me is a PITA while underway. There is another icon that allows you to view how much fuel you have, it gives you a visual of the tank, range, gallons per hour and some information that is nice, but again, you have to scroll through screens to find what you are looking for. There is a favorites page where you can select your favorite screens from any group, and it will automatically scroll through them every so many seconds, this makes it easier to see the things you want to see while your underway, but again if you want to pull something up right away or see something in particular you have to take your eyes off the water to go through a few buttons. Don't get me wrong, there are a ton of awesome features on the smart craft unit, and apparently a lot of people prefer it now, but it takes some getting used to and I actually like conventional gauges better, easier to just know where to look and be able to look, not have to think about what buttons you need to press to find it. Just my opinion.
 
Aye Philyteach wanted to say thanks for the link Mercury SmartCraft! I lost my owners manual and of course now I have it on my desk top now thanks to your link.
Thanks Again,
Kenichi
 
If the engines are really wired you will have a purple plug by the controllercomputer which would plug into a cable you would have to buy. Here is a picture...

Smartcraft001.jpg


Those cable would run to a smartcraft junction box kind of like this

4783_reg.jpg


Then you will have to get a cable to run to the 5000 or for about $350 you could go with duel SC1000

http://www.boatfix.com/bykeywordmerc.asp?textfield=smartcraft&texttype=2

Good luck
Niles
 
I have the smart craft gauges on my new boat a 2008 Maxum 2700. They are a digital readout in the bottom part of the analog gauges. The RPM in measured in 10's but the part I like the best is the instant fuel flow which allows you to get your best mileage when travelling. The fuel flow and gallons used are done on a flow sensor(I think) but the fuel gauge is hooked up to the tank sending unit and shows the same as the analog gauge, which is not always that accurate, so you can cross reference with fuel used. I like the smart craft idea but for quick readouts I still look at the analog gauges because you have to scroll from screen to screen on the digital ones.

bmax
 
My $400 was simply a cable for each engine and a two small gauges. I did not get mine from smartcraft but from Livorsi, as I needed it to match my analog gauges.
 
If you get a newer Northstar Chartplotter it will interface to the Smartcraft Computer. I have been told that Fuel flow, interestingly enough, is computed by Smartcraft by knowing what the pulse rates are on the fuel injectors as they fire. And the fuel computer turns out to be pretty accurate to boot. I have a Northstar 550 with GPS interfaced to mine and besides giving you GPS speeds you can also display six other Smartcraft functions of your choice such as oil pressure, water temperature, battery voltage, etc.

Here are a few pictures of my Northstar 550.

DSC02560.jpg


DSC03096.jpg
 
I am almost positive Smart Craft engines have the sensors and get most of the data from the ECM on each engine. Kida, I don't know what they cost because they were part of a large re-power project. I can ask the mechanic tomorrow I'm down on the boat now. As far as ease of use once you get used to it you won't have any problems. You can even set some pages to view what you want. I did not go the Northstar plotter route because I wanted my plotters seperate from engine monitoring.
Regards Bill
 
Also, when you look at your engine keep in mind that the plug nwaring was talking about may not be in plain sight. I KNEW my engine was prewire and still spent about an hour looking for the end to plug in. I finally called Merc and they gave me 3 or 4 commons spots that the installer might have secured it to. They were right on the 3rd try. Bottom port side of the engine has a little "nub" sticking out that it was wire tied to. After I found it I spent another 5 minutes swearing at Trophy for putting it in such a stupid place, 10 seconds plugging it in and about a half hour fishing it neatly to my console. Total install time (less search) about 3 beers.

edit: Kenichi, your welcome...almost forgot my manners :)
 
Phily, I to had a hard time finding it also and must of spent an hour. Mine was up on top kind of on the port side of the engine toward the back. The boat was a Rinker. The Merc tech people had told me to look for the purple plug but it ended up there was a cap on it and no purple showed.

As far as using the SC1000. It will give all the info you want but you have to press a button to move to the next screenfunction. The good thing is you can program it to only show what you want. I had mine set to only show gallons used, GPH and RPM. The rest of your gauges should be fine to show oil presure and such.
Niles
 
Back
Top