Two New Problems=one Problem Solved

gcolton

Well-known member
Member
Joined
Aug 10, 2002
RO Number
9708
Messages
2,581
When heading out to go fishing yesterday I found that I could not get the engines over 3,000 rpm. This WAS NOT a full throttle setting. The 3,000 rpm (and about 19mph which is close to normal for this rpm) were achieved at about the same throttle position as normal. There was a lot of throttle control movement left, it just did not make any difference. This was not a slowly developing problem. The last time I ran the boat, a couple of weeks ago, everything ran fine.

I had a diver check and clean the bottom and all running gear. He said the shafts were pretty dirty, but that the props were not very bad. I did not have time for a run after the cleaning, but I am not expecting any difference based on the divers comments.

A separate problem is that I am having problems removing the raw water filters. It is time for an inspection/cleaning and I can not budge either. Must have overtightened the last time they were off. Anybody have any tricks?

G
 
From my experience from just a couple weeks ago, I suggest you check plugs and wires.

I had *exactly* the same problem and believe it or not, it turned out I had one fouled plug on starboard and a bad cable (which fouled the plug) on port. Changed the plugs and it's back to perfect. Hard to believe they happened at the same time, but they did.

I don't know about the filters... Maybe a little liquid wrench? That stuff works wonders for me.
 
I had pretty much ruled out two simultaneous problems, one on each engine, as improbable, but worth a check.

Thanks.

G
 
were you using a synchronizer? If so try with it off
 
quote:

Originally posted by gcolton

I had pretty much ruled out two simultaneous problems, one on each engine, as improbable, but worth a check.





Yep. So did I, but that led me to diagnose for two solid weeks to no avail.

Of course, it's relatively easy to check for spark or fouled plugs. My plugs were original (from 01) so it was time anyway. I just wish I had done that first. :)
 
"not very bad" means it was bad... so i'd try another run before worrying about this...

what kind of boat/engines?

Raw water filter? are you talking about the strainers? what kind? I really prefer those with 2 wingnuts over the ones where the cover screws in. if you have these, you'll have to get a pipe wrench... make sure the sea cock is closed first though! :-)
 
quote:

Originally posted by pdecat

were you using a synchronizer? If so try with it off






Even though I was not using the synch that was my first thought but my mechanic says that would not do it. I am still not completely convinced. If I knew what I was looking for I would physically disconnect.

G
 
quote:

Originally posted by PascalG

"not very bad" means it was bad... so i'd try another run before worrying about this...

what kind of boat/engines?

Raw water filter? are you talking about the strainers? what kind? I really prefer those with 2 wingnuts over the ones where the cover screws in. if you have these, you'll have to get a pipe wrench... make sure the sea cock is closed first though! :-)






A pursuit 3000 with Merc 350 MPI mags.

Yes, I am talking about the strainers. They are the type that screws in with the triangular holes into which you fit a two pronged spanner. All of the strainers on the boat are of this type.

Yes, seacock must be closed!! At least they work freely as I had them closed.

Had not thought of a pipe wrench. Will take one with me and see if there is room for it to fit.

One of the problems is that there is not much room around these strainers.

Thanks for the ideas.

George
 
i doubt you have a synch problem... what sync do you have? if GlenD, it's really fail safe as along as it's off.

i dont' like those strainers, they're not built as strong as the grocos, i think they only have two rods holding them together instead of 4.
 
I do not know what type of Synchronizers. In fact I am only assuming I have them because of the switch and breaker. I have never used nor investigated.

The strainers are Groco BVS -1500.

That problem is solved. A pipe wrench will not fit because of the way they are made.

A blunt end punch and a 2 pound hammer solved the problem. A few taps and all I needed to see was any movement of the screw on top.

Everything was still very clean so the job was then easy. A little spraying with some Teflon white grease and I expect no more problems in the future.

Soon I will get the boat out and see if the gear cleaning made any difference.

George
 
with twins if one engine is weak the other will rev a bit higher but not reach wot as it is over loaded. both engines limited to 3000 rpm points to control placed on the good engine, a weak master engine and the slave following it because of the synchro. unless they were sharing the same fuel line I cant think of any other reason they have identical rpm limits.
 
Some (all?) of you may be wondering why this idiot does not know the equipment on his boat?

The answer is simple. I bought the boat from a broker who knew nothing about it. The owner was in a coma and dying from cancer so I was not able to talk to him. I have learned a little from the original owner, but he does not seem to remember much. Pursuit has been good about checking and answering my questions as best as they can. In this case I have just never been interested in learning about an engine synchronizer as I have not wanted to use it. The manuals are good, but they do not tell if a system was installed or not.

I know that just because there is a synchronizer switch it does not mean that a system is there or if it is there that it is operable. When Pursuit opens Tuesday I will call and see if they have answer.

I believe that I am the fourth owner of this boat. One item that I cannot believe was never corrected from the factory was the helm station "hold downs." The helm station is hinged at the bottom so that you can access the back. There are supposed to be two over center can locks that hold the hinged station to the solid boat structure. These were never installed at the factory (I know they were never installed because there are no holes) and the station moved considerably when running over waves. I asked the original owner and he could not remember anything about this. I do not know how anybody was able to operate this boat without the helm station being solid. I ordered the hold downs from Pursuit and the station is now solid.

I am learning about systems on this boat all of the time. I am sure there are still surprises in the future.
 
if you have mechanical throttle cables they will either go direct to to each engine or to a box then to the engines. The box is the synchro. Electronic systems will be very different.
 
well, you need to spend some quality time with your boat.. crawl everywhere, find eveything, ID everything.

Glendining is a very popular and probalby the most common type of Synch. easy to spot... it's gold alum box about 12x3x4 attached to your throttle cables... cant' miss it. if that's what you have, and it's off, then it's unlikly to cause problems. You cna find the manual on their site, very clever and simple system

otherwise, Bruce is right, if one engine is weak, the other one ins't going to be turn much more RPM because of propping...
 
Back
Top