Water heater

purl

Member
Joined
Jul 26, 2005
RO Number
18418
Messages
27
My boatin buddy has a 1992 Cadorette Holiday 260 cruiser.We put in at our marina this weekend and plugged in to our 30a services.This morning he had no hot water.The breaker in his on board panel wasn't "popped" and everything else electrical was fine (electric stove,microwave etc). The voltmeter at the panel showed good voltage of about 120vac.We cycled the breaker for the water heater a few times but after some hours still no hot water.Would there normally be another 110v fuse for these heaters located somewhere other than the breaker panel?The heater was working fine when the boat was put into storage last fall. Thanks for any input..
 
Check the wiring into the heater..it may have been disconnected or bumped during winterization for some reason, ...
If you have power to the heating element, then replace the element...If the heater was left on with no water in it last fall during winterization, then the element will be fried...
 
Purl,
Since the breaker was tripped, this indicates one of three possibilities, either a dead shorting condition, an amperage spike, or a thermal overload, i.e. the breaker or the wiring into the breaker got too hot. There are not other circuit protection devices, the breaker on the panel is it. You need to do some troubleshooting first to find out what caused that breaker to trip...
thcorn.gif
 
I missed the part where the breaker was tripped...I thought that it wasn't "popped" ?...
 
The breaker was not blown. My main concern was if there would normally be another fuse in the circuit between the breaker and the tank.I didn't have a voltmeter,so next time I'll check the voltage at the load side of the breaker then for voltage at the tank.
Thanks for the responses
 
Check the heater unit for a small thermal switch. It will look like a little red button. If the heater did not have enough water in it, this will cause the thermmal switch to trip. If you find this (typically where the wiring enters the heater)just push it in to reset.Just make sure unit is full of water before you try again. Hope this helps
 
quote:

Originally posted by ernstjrb

Check the heater unit for a small thermal switch. It will look like a little red button. If the heater did not have enough water in it, this will cause the thermmal switch to trip. If you find this (typically where the wiring enters the heater)just push it in to reset.Just make sure unit is full of water before you try again. Hope this helps





Ditto. My water heater has a reset button on the heater. The cover must be removed from the heater to access it.
 
Sounds like you put power to it before it had water in it and burned out the element.
 
I think all water heaters have a Thermostat and a heating element under a cover.
It could be either of those.
When you first turn it on, in a few seconds you might hear a hissing sound, with that and still no hot water its probably the Thrermostat.
 
quote:

Originally posted by carver 2557

I missed the part where the breaker was tripped...I thought that it wasn't "popped" ?...






My bad...[:-ashamed]
 
There should only be the primary breaker for the hotwater heater and no in line fuse. What manufacture and model is the heater? Does the heater also have a heat exchanger from the engine if so after running the engine do you have hot water? I always like to run one of my hot water taps when the boat comes out of storage so there is not potential for an air pocket in the heater. While heaters have a simple thermostst to control the heating element if there is no water for the control to sense temperature you may have opened the heating element.
 
Positive, I have never seen an in line AC fuse for a high current device other than some older Marine Trader Trawlers but the fuses are at the panel. There is no ABYC electrical requirement other than the heater be ignition protected assuming this is a gas powered boat, the wire feeding it be the correct type (marine grade stranded 3 conductor), the proper gauge wire and the panel's circuit breaker sized accordingly. I am a member of the ABYC and am current with AC & DC requirements.
A simple test would be to open the heaters wire connection plate and check for 110VAC with a meter.
I think you will find the voltage there so it's either the reset button, a bad connection or an open heating element.
Please report what you find.
Bill
 
Was the water heater bypassed during winterization and not re-connected?
 
Excellent Greg...That is quite common to do and I never thought of that when I answered...Damn your good...
 
quote:

Originally posted by Sandy

quote:

Originally posted by Billylll

There should only be the primary breaker for the hotwater heater and no in line fuse.





Just asking since I have no HW heater onboard: Are you sure there would be no inline fuse? I thought USCG regs or at least ABYC(?) standards say only the engine starter circuit is exempt from requirement of a fuse or breaker within less than a foot from the the battery or battery sw on the supply side to protect the wiring toward the main panel breaker.







Sandy you are confusing AC and DC circuits. You are correct about no fuse off the batteries for the engine starter in most boat's there are no starter fuses.
However when it comes to AC your shore inlet (receptical) must be fused if the run is over 6 feet from the main panel. In that case an entire AC leg would be dead so he wouldn't have 110VAC at the Microwave or Stove as posted above. As far as I know there are no DC hotwater heaters on boats.
Greg S good point but I would think if the hoses were disconnected to the waterheater his bilge pump would be running.
Bill
 
The tank was not bypassed during winterization.We ran at least 2 holding tanks(50gls) of fresh water through the entire system hot and cold opening all taps to rid the system of air and antifreeze after winter storage.The tank does have a heat exchanger but we didn't run the boat for any more than 5 minutes just to get it from the launch to the slip.We'll try some of the suggestions posted here and post our findings.
Thanks to all.
 
Check for AC voltage at the heating element. If you have (nominal 115 V) voltage there, the element's burned out. Very common in the spring when commissioning the boat. Power gets unknowingly turned on before water heater has been filled with water. Only takes about 30 seconds to burn out the element if it isn't immersed in water.
 
quote:

Originally posted by seabob4

Purl,
Since the breaker was tripped, this indicates one of three possibilities, either a dead shorting condition, an amperage spike, or a thermal overload, i.e. the breaker or the wiring into the breaker got too hot. There are not other circuit protection devices, the breaker on the panel is it. You need to do some troubleshooting first to find out what caused that breaker to trip...
thcorn.gif






SeaBob4 why do you have a link to another boating message board under your picture? This isn't allowed on this board.
Bill
 
Back
Top