whistling shaft

patsab

Member
exMember
Joined
May 29, 2005
RO Number
17582
Messages
104
put boat in water yesterday. on way out of river hit a submerged lobster pot. stopped right away and then put port in reverse and pot came out in three pieces. Continued to my marina with no problems. Cruised over at 3200 rpm and had ni issues. Today took boat out and after an hour my port shaft would make a whisling sound at idle speed. Attributed it to hitting lobster pot. Soon later even starboard started to whistle. Boat is 1998 wellcraft martinique 3200 with 454 mercruisers and dripless shafts. any ideas what this can be. Am I having an issue with dripless ?
 
Perhaps line wrapped on shafts is preventing water flow to dripless seals. Or maybe your water injection line to dripless seals is clogged. Burp the seals and clean bearing surface with clean cloth, then perhaps you should get a diver to look at shafts.
 
Sometimes when the cutlass bearings are bad, you hear a slight
knocking when idling. I never heard a whistling shaft. New one
to me.
Be sure to let us know in case it happens to us. That one might
be hard to find.
You might get someone to put their head in the engine compartment
while you idle to see if they can find out if it is the transmission
or the glands.....
I can't understand the cutlass bearings whistling if they have water
running thru them.
 
Sounds like you need to take a dive down to take a look or hoist the boat up for an even better look.
 
Hauling for a good inspection of the running gear would have to be the best way, but I'd think you'd want to get under there or at least hire an experienced hull diver to do it for you. You could be scoring the shaft which can lead to breakage. If you have shaft anodes , they may have been pulled down to the cutlass, though that is usually more of a grating noise, & there may or may not be line still on the shaft. Even if they are missing now, the zincs may have left particles in the cutlass. In some cases singing can come from a dinged prop leading edge & sound like a newly serviced prop sometimes does. if the pot and warp were around both shafts it may have pulled the shaft toward each other , bending the struts inward and creating just enough constant friction on the cutlasses to "sing " until the cutlass rubber wears away. The water supply to the shaft seals was a good thought by Robbins- were the seals getting hot?

After fouling like that, I'd strongly suggest -always inspect at 1st safe time to help prevent greater problems.
 
Went down to boat today and put each transmission in forward while tied to dock and as soon as starboard was put in gear it started to sing at idle.Will be going down tomorrow to get a better look and most likely get a diver down to take a look. Would love to go down myself but water is a bit too cold right now!!!!!
 
Sure sounds like friction of some sort, I just splashed after a week out of the water and as soon as I put her in gear my wife and I heard a whistle sound. We both looked at each other and said did you hear that, by then it was over.
I figured it was dry and as soon as the water began to lube in all was good again. Took it out again Sturday and no whistle sounds. Do let us know what ya find.
 
My boat lives on the west coast of Florida 10 months a year. The other two months it goes to the Florida keys. When up north I never get any sound from the shafts but when in the keys, the shafts "sing" at idle RPMs. I paniced the first time I heard it but it's been doing it for 5 years so I got used to it. I wish I knew what caused it.
 
PYI states their dripless shafts will sing if the coupler doesn't get the needed water supply. I'm guessing the coupler water supply comes out of the riser, which tends to clog. Bob
 
Went under boat today. shaft zincs on both shafts slid down and was rubbing on cutlass . Easy fix for a change. Was worried something major was wrong. Thanks for help....
 
Back
Top