Cutlass bearing problem?

Mule

Member
exMember
Joined
Mar 3, 2002
RO Number
7719
Messages
74
I got a 1/4" yellow nylon rope wrapped around my starboard engine prop shaft.
Fortunately, I was able to cut all the line off.
Upon further inspection (underwater with a mask on), I noticed that some of the rope is stuck in the cutlass bearing. I pulled as much as I could out but there is still some in it.
I can turn the prop by hand and it doesn't seem stiff but is this something to be overly concerned with? Should I have the prop removed and the cutlass replaced / cleaned?
Thanks for the info!
 
I'd be inclined to leave it but keep a very close eye on it. The piece may work its way out or do no harm att all.
 
I'd get it out if you can. It can solidify and become harder than the rubber bearing. And then eat it away.
 
Thanks for the input.
I'm gonna leave it alone. I'll check it again in a few weeks!
 
if the line in the cutlass bearing is fatter than a few thousand's of an inch, it will push the shaft to one side of the bearing and cause it to wear on the bearing. it will shorten the life of the bearing as the water flow is restricted. one way or another you will be pulling the shaft to clear this, either now or later to replace it. if you can get a pressure cleaner down there and try to dislodge it in place its worth a try.
 
You don't necessarily have to remove shaft to remove cutlass bearing.
 
If you can see fibers try pulling them with a needlenose visegrip while easing the wheel back & forth.
 
How do you replace the cutlass bearing without removing the prop and shaft? I have to have mine done tomorrow and if I can avoid removing the prop and shaft, I'd be happy.
 
MichaelNJ, I never said you didn't have to remove prop. That must come off to remove & replace new bearing. There is equipment available to remove & replace cutlass w/o removing shaft. Had mine done this spring by yard. I removed prop & set screws from strut. I supplied bearing & they did the labor for $100.00 . Good deal for me !
 
They told me 45 min at $95 / hr. to remove the old and install a new bearing if the shaft is removed.
 
You can remove the stenchens if the boat is hauled after removing the props and take them into the shop and press the bearings out with a socket wrench of the right size and press a new one back in and re attached the stenchen, sealing it of course.
 
Stenchens = Struts ???

If boat is hauled & shaft is out why would you want to remove the stenchen? if all you're going to do it push out old & press in new. May as well do it while stenchen? is still attached !
Most half decent yards have hydraulic device to remove & replace with shaft in place.
 
Removing the strut would mean re-aligning it after you replace it. Much extra work, time and money.
 
I was told yesterday that the strut is put on with 5200 and removing it would damage the fiberglass.

You definitelty do not need to remove the strut from the hull to replace the cutlass bearing. I see not advantage in doing so.
 
Michael,

How do you know you need a new cutlass bearing? are you getting a lot of vibration, or was there some other damage?

Thanks!
 
quote:

Originally posted by MarkGibson61611

Michael,

How do you know you need a new cutlass bearing? are you getting a lot of vibration, or was there some other damage?

Thanks!






true that, after 20 years my oem bearing looked pretty good considering the conditions
 
Sorry for using the wrong term but on my boat the struts are bolted in and yes they had 5200 on them but as the hull was gel coated on both the in and out side the 5200 came off pretty easy. As far as alignment, the bolt holes were very tight and it was much less work than removing the shaft on my v-drives and the alignment was no problem. Between the props and the cutless bearing I gained 1 knot a cruise.

Tha haulout, parts (bearings) and labor including getting my props redone was $800.
 
Back
Top