Looking for info

Shane- Looks interesting. I couldn't open any of the interior shots.
I should be available this weekend- want me to tag along for moral support?
E-mail me- I lost yours.
Rob
 
Rob,

I have your email at work. I will try to remember to email you. Would be great to have another set of eyes there. If you don't hear from me, give me a call.

-Shane
 
Sometimes when asking for feedback, you may not want to dictate the terms of the feedback. I can see how some of the respondents were put off.

Lots of us have been down the path you are travelling. Even if your labor is free (which its not), that boat is not going to be a "bargain". It's going to cost more to put back running than the price of just buying one that is in better shape.

A non running boat is not worth $2K in my opinion. The owner is not doing you a favor. Just my opinion, having been there.

Realize that prop sizes are not something you can exactly take right off another boat. Every boat is a little different in weight and the owners needs. That said, given a pair of 318's and 71C direct drives, I can tell you that 14x10 will probably be in the ballpark, but expect to adjust props at least twice to hit the sweet spot. Given the low pitch for the blade diameter, I would be surprised if you could not improve on that combination.

I'm not certain, and its been a few years since I've owned/rebuilt/replaced 318's but I don't think I'm seeing the heat exchanger that I recognize. Are these then raw water cooled? If so, they are likely at their lifes end. The oil coolers look rustballed, but are not expensive. Plan on new risers all around, manifolds too if raw water cooled. The carbs on these things are a tricky rebuild and replacements are likely a better option. 318 parts are on the expensive side. 225's will cruise around 8gph each or so.

I can't say that my project boats were good investments. I would have been much much better off with something requiring less work, given the costs involved. It did teach me a lot of things though that have saved me a lot of money avoiding other money pits. YMMV.

Good luck. Try to keep an open mind. Given you will easily be in this boat for over 7K just to have it running, not complete. Realize at 5K there are boats out there that run that have new risers and such already on them. Don't underbid the job.

bp
 
My intent was not to dictate the terms of the feedback, but I forsaw the "get a survey" comments coming, I have been around on this board for over 6 years. Rather than have people waste their time telling me to get a survey, when I knew that I have absolutely no plans of getting one, I pointed out in the first post that I would not be getting one. Guess it was pointless after all.
 
<<sigh>>

Obviously we still disagree on the "best" approach. So be it. But you deserve to hear the reason -why- a survey was recommended.

What you have is not a $3500 project. What you have is a $45,000, the first expense of which is $3500. In this respect, any one individual $600 expense is small. Since a survey would a) answer virtually all of your questions, b) possibly find things that you missed or unqualified to diagnose and c) quite possibly provide you with workarounds or fixes that you were unaware of, or that would cost less than you were anticipating.

For these reasons, an attempt was made to help you get the project moving in a time and cost effective way. It is also important to understand that many of us answer your questions not -just- to answer -you-, but to help and inform other readers of this thread who nave not ( yet ) posted their specific question. So, often an answer will exceed the bounds of the original question.

I do hope you succeed in this project, though I have a gut feeling that one or more of your limits may be exceeded ( cost or time ). I could easily be wrong on this, and look forward to hearing how you do it.

Good luck and happy, safe boating!
 
After reviewing the pics, you will have a lot of work on that boat to get her truly shipshape...On boats that have sat for a while, with a reasonable amount of previous owner neglect, you will be fixing large and small problems alike for years to come.

You already have a boat, so you should have a good idea how just a few trips to the parts store can add up to over a thousand dollars before you blink an eye. Just on the electrical side as simple as bildge pumps/switches rewiring is going to cost more than you think.

If it were me and you cannot front the few extra grand for a more "turn key" boat, I would keep the bayliner. I have gone down the road you are on a much larger scale with my Hatt, which was sold and presented as turnkey, and basically, the "minor repairs" equalled the price of a boat a few years later. Also, keep in mind, I did fork out the dough for a survey.

Just from my experience,

-Mike
 
After reviewing the pix, I am very leary of the interior surface rust. Do you know anybody in the Non Destructive Testing (NDT) business. I am very concerned about the thickness of the metal from the original specs.

After reviewing the pix, I am standing by my original estimate. The question is not can it be done, it is more a question of is it worth the added expense.

I wish you well. Keep us posted.
 
David>> That is not rust, just a bilge with years of build up... The hull is Aluminum. Not sure I would even be interested in it if it were steel
 
Mike,

I agree that there are alot of small things that will nickel and dime me, items that even a survey would not turn up. I am figuring on putting 5-7k into it over then next few years (aside from the usual stuff), and hoping that it turns out less. I am ok with it being a water front condo for this year if need be.

Buying this boat is not a decision that I take lightly. I have been pondering, and weighing for almost 2 years now... We will see what happens with the engine check up on Sunday.

Thanks to everyone for your input and advice. I will keep everyone updated as to how things work out.
 
quote:

Originally posted by tr_guy79

David>> That is not rust, just a bilge with years of build up... The hull is Aluminum. Not sure I would even be interested in it if it were steel






Then again, do you know anybody with an NDT business? Their tools could give you a definitive start point with regards to hull integrity/welds/etc.....

If not, tap the entire hull with a rubber mallet. Listen for the "odd" sounds.
 
tr_guy79,
Do you have any contact with your Caterpillar tractor dealer? They have tooling that will measure the hull thickness without damaging it and it only takes a few minutes. They use this same technology to measure the thickness of track links, but it works on aluminum also. May save you a few headaches or suprises down the road.
 
With young children on board, I would make sure the hull is safe. It's one thing to go out in the water with a tear in a cushion and another to have boat that may have a hull issue.
 
Back
Top