Looking for info

It lowers the chance of corrosion, and opens up the possibilities of Antifoul paints that can be used. If I am wrong let me know. From what I have read, the the whole process is a HUGE PITA....

-Shane
 
David,

I am not really clear as to their origin, but will check into it tomorrow when I am down there. I have tried finding pictures online of the original setup on the '32, but no luck so far. STILL waiting for my membership on the Marinette forum to be approved...
 
Sounds like it Shane. Would the barrier be some kind of epoxy so that copper based paints could be used on an alluminum hull?
 
Shane:
As others have said, insurance may be hard to come by without a survey. A few years ago I bought a junker and refurbished it. I didn't have the boat surveyed when I initially purchased it, for the same reasons you don't want to. After I did all the refurbishing and it was ready to go in the water I paid for an insurance survey. The entire survey was done on the hard. No seatrial required. I then submitted the surveyors report to the insurance company and they wrote me a policy.

FWIW
eric
 
Good luck with it. A friend of mine has 32 ft. also. He has kept it just about perfect condition. I do know it take special anodes for the hull. As far as the props and rudders, he could probaly tell you what size his are. Ricky
 
Eric- I would likely be going the same route. No insurance is required, but I will likley insure it anyway. I highly doubt it would pass an insurance survey as it sits, so there is no point in getting it done now given the cost ratios. Would be kind of like me going and taking the MCATS. I would only be spending money to find out what I basically already know (or don't for that matter)

Ricky - If you could put me in touch with him, that would be AWESOME!!! I will owe you a cold one for sure.
 
A word from the wise if you were to have an environmental mess with this boat as in a sinking or major fuel spill you will wish you had insurance. The EPA loves to make the average Joe go bankrupt in the name of saving the environment. Bill
 
You're going to need at least libility insurance to protect your assets (current and future) and to be permitted to dock at any marina.
 
Gregory, you beat me to it. However, I don't believe a survey is required if all one wants is liablity insurance, I have liability on my boat and haven't had a survey.
 
I would think you are correct but I don't know. I'd be pretty nervous with an uninsured boat anywhere near mine in a marina.
 
It may depend on the amount of insurance you are buying ... I insured my 1995 boat for 30K with Progressive with no survey!!
 
Shane - I looked at a boat like yours and loved it. It wasn't quite the project that you are thinking of taking on but it sounds like you understand the risk you are taking. You do need to be careful with the aluminum hull, there are some interesting articles on "catastrophic failure" of aluminum hulls because somebody didn't understand the way metals interact with each other. That said, there are some advantages to aluminum, one of them being that the hull is light which helps fuel consumption. Godd luck!

Definatley a high risk / high reward situation but no guts, no glory.

Jim
 
Shane what kind of shape is the interior in? Looks like an interesting boat. I saw where you are familiar with DC wiring I hope you mean marine DC wiring there are some differences. If possible post some pictures here this board has a wealth of knowledge on it. It sounds to me that if you can purchase the boat with the shafts and rudders do so, you could very easily exceed the $1500 difference in price if you need to find and purchase new ones for that boat. Best of luck with her just keep your mind and eyes open these restoration projects can take on a life of their own.
Bill
 
quick bit of advice. with you and the wife and 2 year old onboard, you'll want a windlass for hauling the anchor. otherwise, while you're on the fordeck wrestling with the ground tackle, the wife will be on the flybridge wrestling with the two year old and she won't be able to maneuver the boat as needed. been there. so much easier with the windlass.
 
I believe that you will be able to get liability insurance even if it is only on yourself or an umbrella on your other (auto?) insurances. The survey is necessary for insuring the property (boat) against losses where the property value is in question.
 
All:

Thanks for the replies. I went and looked at the boat on Saturday. Either on my lunch break, or tonight at home, I will post up the findings and some pictures...

-Shane
 
I have liability only insurance for my boat from BoatUS. At the time I applied, they told me if my boat were 15 yrs or older, they would require a survey. At 14 yrs then, I squeaked by. If I tried to change insurance companies, I'd probably be denied without a survey now. I have only had one insurance claim for my boat, about 10 yrs ago. It was fully insured at that time.
 
quote:

Originally posted by tr_guy79

My impression is that a survey costs about $600, and on a $3500 boat, that just is bad fiscal planning. Anything that is wrong with the boat I will be fixing myself, with the exception of the bottom painting, which sounds to be a real PITA. My reason for the "Krylon" question is that it is cheap, quick, and easy, and if it got me through 1 or 2 seasons looking decent, it would be worth it.






$600. can save $60,000. in unseen nightmares.

And like your quote says, the warm pee in your pants can turn awfully cold quickly in a bargain boat-buyer beware. Get a survey.
 
Quick update... long day... gotta get to bed.

Went over the boat with fine tooth comb. The only things new I found:

1. (one of) The previous owner's FCC EPIRB liscence
2. Both engines turn over by hand
3. Velvet 71c 1:1
4. Has been repowered most likely. Has 235hp 5.2 w/ electronic ign, not std. 225hp 5.2
5. No corrosion to be found, except in random spots on the vertical ribs on the in side of the hull
6. Each engine has (1) cracked exhaust elbow. Figuring on it all needing redone
7. Hour meter show 1035

Going back down this weekend to do a compression check, and see if I can get them to fire.








Is anyone able to ID these engines, or decode the serial # for the boat (No HIN)







Some outside shots







And the current hole...ahem... I mean boat...



I'll update again, with this weekends findings.

-Shane
 
Lots of Marinettes on Lake Erie, very popular boats. The aluminum hull(like everything in life) has ups and downs. Very strong, I've seen Marinettes on the water that "have run up on the rocks" and are still afloat. Many people simply beat the dents back out of them. If you have experience welding aluminum these hulls are easily repaired. There is a fuel savings also, although don't expect much. The light hull has downsides also, watch out in high wind, they are pushed around fairly easily. In fresh water they can last a lifetime, and normally do. I don't have any experience with these in salt water.
 
Back
Top