Water Maker Question, 2nd Thread

How Z-Brane™ Works
As water enters the membrane it is exposed to a powerful electrostatic field of the electrode charging all water molecules in a positive orientation. This positive charge prevents particulates from bonding to one another, preventing the formation of sludge, scale and biological fouling. The wetted charged surfaces form a strong boundary layer preventing particles from bonding. Bacteria are rendered inactive and unable to absorb nutrition to replicate into colonies. With the Z-Brane™ you can prevent watermachine membrane fouling and scaling now and forever.

Yes it is installed in the membrane tubes.
Bill
 
We have a Village Marine unit. It's their 12v system rated at 10 GPH. It has never produced water at that rate in the Bahamas, and now after arriving here and firing it up, yet again it has let us down. Last year a membrane died, and this year it is now making water at 500ppm and 7 gph instead of 10 or 12. All of the pressures look good and there is plenty of rejected water flow. Initially this year we made water at 10 gph and about 200 ppm. But over here it's junk yet again.

We've back flushed it with fresh water that has no chlorine in it. In fact we've tested it every time prior to flushing. All we did was go from the East Coast to the Bahamas and the system is dead again.
 
I decided to invest $10 and went to the big "E" and bought a set of plans, including a complete parts list with costs. I am going to build my own, very basic, system. For my little 28' boat that will suffice very well.

The system schematic look exactly like the "factory" systems and with buying exactly the parts from the list the complete system will cost about $1500.

Yes, the system will be very basic and, for the most part, manual, but for me that's OK. I've always been a big fan of the KISS system.

Also, the schematic shows how to build in a second membrane if increased capacity is wanted/needed. Very simple to do.

Bob

PS: I enjoy a good challenge! :)
 
Good for you Bob, we are ready to throw this one out. Perhaps I may opt to swap out the membranes for a generic version. What PPM are you shooting for?
 
quote:

Originally posted by boatbum

Good for you Bob, we are ready to throw this one out. Perhaps I may opt to swap out the membranes for a generic version. What PPM are you shooting for?






<200 ppm is what the membrane spec's say. Operating pressure is 800 psi.

Bob
 
quote:

Originally posted by rnbenton

I decided to invest $10 and went to the big "E" and bought a set of plans, including a complete parts list with costs. I am going to build my own, very basic, system. For my little 28' boat that will suffice very well.

>snip<

Bob

PS: I enjoy a good challenge! :)






Sounds like a good plan. And in the end you'll know your system inside and out.
 
Bob: have you found a cheape source of membranes??
 
I thought so but Bob plans to build a complete system for $1500. Unless he is using a bilge pump and some racors he must have cheap membranes.
 
quote:

Originally posted by pdecat

Bob: have you found a cheape source of membranes??






Why does this feel like a loaded question? :)

Are you asking about just the membrane or the module consisting of both the membrane and pressure vessel?

From what I have found out about 99% of the membranes are made by Filmtec.

Lots of distributors on the internet.

The only "expensive" parts to a simple water maker are the high pressure pump, motor, membrane and pressure vessel.The rest of it a just tubing, hose and fittings most of which can be bought at any Lowe's or Home Depot.

Admittedly I was a little off on my initial calculation:

Pressure pump $675
Motor $310
Pressure Vessel $200
Membrane $170
Feed pump $30
Double pre-filter $25
Pressure gauge $40
Needle Valve $30

Total $1480

Than there's about $150 in tubing, hose, T's, nipples, etc.

Bob
 
Dan I know there are chemicals you can try to bring back your membrane depending on the damage. Oil damage or contamination can be reversed. Take a look at some of the chemicals available on the Spectra site they tell you what they can or can't do with the membrane.
Bill
 
Not loaded I am wondering if I can get cheaper stuff and repair my watermaker.
 
so why not just buy a pressure washer motor and pump for $150?
 
A 170 gpd membrane filmtec brand can be bought for 180 bucks. If you buy it from the place that sells them for the watermaker they will get three times that.
 
quote:

Originally posted by PascalG

$30 for the feed pump??






Yes, Sureflo 100-000-020 is about $30 depending on where you buy it.

OK, $32.50 to be exact.

Bob
 
After installing my Katadyn (okay, Bill's Katadyn), I'm going to say that Bob is completely correct in his component list and the prices. These devices do not need to cost thousands of dollars for a basic system. There's not that much to the basic units. And like Bruce, I'm anxious to hear where the affordable replacement parts can be found!
 
Back
Top